How-To

How to Reset a Gas Water Heater: A Step-by-Step Guide

Gas water heaters are one of the most common ways to provide hot water to homes and businesses. However, like any appliance, they can experience problems that require troubleshooting. One common issue is the need to reset the gas water heater. This can be caused by a tripped safety device or a malfunctioning thermostat. In this article, we’ll provide a step-by-step guide on how to reset a gas water heater to help you get back to enjoying hot showers and clean dishes.

Turn Off the Gas Supply

The first step in resetting a gas water heater is to turn off the gas supply. This is essential for safety reasons, as gas leaks can be dangerous. Locate the gas valve on the water heater, which is typically located near the bottom of the unit. Turn the valve clockwise to shut off the gas supply to the water heater.

Once the gas supply is shut off, it’s a good idea to wait a few minutes to allow any gas that may be present to dissipate. This will reduce the risk of a fire or explosion. While you’re waiting, you can move on to the next step of shutting off the water supply.

Shut Off the Water Supply

The next step is to shut off the water supply to the gas water heater. This is important to prevent any water from entering the tank while you’re working on it. Locate the cold water supply valve, which is typically located near the top of the unit. Turn the valve clockwise to shut off the water supply to the water heater.

Once the water supply is shut off, you can move on to draining the tank. Draining the tank is an essential step in resetting a gas water heater, as it will remove any sediment or debris that may have built up in the tank.

Shut Off the Water Supply

Shutting off the water supply to the gas water heater is a crucial step in resetting the appliance. This is because it prevents any water from entering the tank while you’re working on it, which can be dangerous. When water enters the tank, it can cause steam to build up, and this can lead to an explosion or other safety hazards.

To shut off the water supply to the gas water heater, locate the cold water supply valve. This valve is usually located near the top of the unit, and it’s connected to a pipe that runs into the tank. Turn the valve clockwise until it stops to shut off the water supply.

After shutting off the water supply, open a hot water faucet to release any pressure that may have built up inside the tank. This will make it easier to drain the tank in the next step.

Drain the Tank

Draining the tank is an essential step in resetting a gas water heater. Over time, sediment and debris can build up inside the tank, and this can affect the efficiency of the appliance. Draining the tank will remove any sediment and debris, and it will also give you a chance to inspect the tank for any signs of damage or wear.

To drain the tank, locate the drain valve near the bottom of the unit. This valve is usually a spigot that’s connected to a hose. Attach a garden hose to the valve and run the other end of the hose to a drain or outside. Open the valve by turning it counterclockwise, and let the water drain out.

Once the tank is empty, close the drain valve and remove the hose. Turn on the cold water supply to the water heater and let it run for a few minutes to flush out any remaining sediment and debris. After flushing out the tank, you can move on to resetting the pilot light.

Reset the Pilot Light

The pilot light is a small flame that ignites the gas burner in the water heater. If the pilot light goes out, the water heater will not function properly. To reset the pilot light, you will need to follow these steps:

  1. Locate the pilot light assembly, which is typically located near the bottom of the water heater.
  2. Turn the gas control knob to the OFF position and wait at least 5 minutes to allow any gas to dissipate.
  3. Locate the pilot light button and press it down while simultaneously pressing down the ignition button. This will ignite the pilot light.
  4. Hold the pilot light button down for about 60 seconds to allow the thermocouple to heat up and keep the pilot light burning.
  5. Release the pilot light button and turn the gas control knob to the ON position.

Once the pilot light is reset, you can move on to turning the water and gas supply back on.

Turn the Water and Gas Supply Back On

The final step in resetting a gas water heater is to turn the water and gas supply back on. This will allow the tank to refill with water and the burner to ignite, providing hot water to your home or business. Here’s how to turn the water and gas supply back on:

  1. Turn the cold water supply valve to the ON position. You should hear water flowing into the tank.
  2. Turn the gas control knob to the ON position. The burner should ignite within a few seconds.
  3. Wait for the water to heat up. It may take a few hours for the water to reach the desired temperature, depending on the size of the tank and the temperature setting.

In conclusion, resetting a gas water heater is a simple process that can save you time and money on repairs. By following these steps, you can safely reset your gas water heater and get back to enjoying hot showers and clean dishes. If you’re not comfortable performing these steps yourself, it’s always a good idea to contact a professional plumber or HVAC technician for assistance.

Related Articles

Back to top button